1.桶板修整與定級干燥時桶板兩端有時會開裂，要將這部分切掉，并仔細檢查每一片桶板是否完好。同時將不同品質的桶板分開。
When repairing and grading and drying the barrel board, there may be cracks at both ends of the barrel board. This part should be cut off and each piece of barrel board should be carefully checked for completeness. Simultaneously separate the barrels of different qualities.
2.整理桶板決定桶板的內外面，雙面切削的機器將桶板加工為理想的形狀，內面是凹面，外面是凸面。
2. Organizing the barrel board determines the inside and outside of the barrel board. A double-sided cutting machine processes the barrel board into an ideal shape, with a concave inner surface and a convex outer surface.
3.拼接桶板桶板拼接是加工桶板邊，這是決定裝桶時桶板彎曲度的關鍵。桶板加工成為中間寬，兩端窄，桶板中間的寬度決定橡木桶的中間直徑。
3. Splicing of barrel plates and barrel plates is the key to determining the bending degree of the barrel plates during loading, as it involves processing the edges of the barrel plates. The barrel board is processed to be wide in the middle and narrow at both ends, and the width in the middle of the barrel board determines the middle diameter of the oak barrel.
4.裝配橡木桶這個步驟是手工操作。將桶板一塊一塊的拼在一個堅實的鐵制桶模上，頂端緊密拼接，末端開放，用幾個制桶篩固定住。
4. The process of assembling oak barrels is a manual operation. Assemble the bucket boards one by one onto a solid iron bucket mold, with the top tightly connected and the end open, and secure with several bucket screens.
5.彎曲成型為了將桶板彎曲成型橡木桶，需要將桶板加熱，有的是用蒸汽加熱，更普遍的是用火烤同時噴水。蒸熱后，用繩子套住開放的那頭，將桶板篩緊，再用制桶篩套住，一個橡木桶體基本成型。
5. Bending Forming In order to bend the barrel board into an oak barrel, it is necessary to heat the barrel board, some of which are heated by steam, and more commonly, they are roasted over fire and sprayed with water. After steaming, wrap a rope around the open end, sieve the barrel tightly, and then use a barrel sieve to wrap it, forming an oak barrel body.
6.烤干、篩桶和烘烤被制桶篩套住的桶板1壓力很大。這時將桶身放到火上烘干為彎板而增加的水分，減輕桶板的壓力。接著用幾個制桶篩將桶身篩住，使桶身受力均衡，逐漸合縫?？靖珊秃Y桶大約30-40分鐘。這時會根據需要烘烤桶身。烘烤度依賴時間而定，時間越長，烘烤度越重。
6. The pressure on the barrel plate 1 that is covered by the barrel sieve during drying, screening, and baking is high. At this point, place the barrel on the fire to dry and increase the moisture content of the bending plate, reducing the pressure on the barrel plate. Next, use several barrel making sieves to screen the barrel body, so that the force on the barrel body is balanced and gradually fits together. Roast and sieve for approximately 30-40 minutes. At this point, the barrel body will be baked as needed. The degree of baking depends on time, and the longer the time, the heavier the degree of baking.
7.烘烤之后，將桶身兩頭用切磨機切磨出端板槽。
After baking, cut and grind the two ends of the barrel body into end plate grooves using a cutting mill.
8.制桶端板制桶端板比較簡單，將桶板放在切削機上切削板邊，磨光。然后一塊一塊拼成桶端板。所有板塊兩端都鉆了釘眼，用木榫釘或合縫鋼釘釘緊。
8. Making the barrel end plate is relatively simple. Place the barrel plate on the cutting machine to cut the edge of the plate and polish it. Then piece by piece, assemble the bucket end plate. All plates were drilled with nail holes at both ends and fastened with wooden tenon nails or joint steel nails.
9.切端板用機器將端板切成規定規格的圓形。端板的 直徑非常關鍵，必須在切之前決定。
9. Cut the end plate into circular shapes with specified specifications using a machine. The diameter of the end plate is crucial and must be determined before cutting.
10.裝端板裝端板時需將桶身一頭的桶篩松開，將端板嵌入后再篩上。
10. When installing the end plate, it is necessary to loosen the barrel sieve at one end of the barrel body, insert the end plate, and then screen it on.
11.完成一個橡木桶將橡木桶里外的污跡清理干凈，方法有多種，機器磨污，或用沙子去污，使橡木桶看上去清潔干凈。
11. Complete an oak barrel to clean the stains inside and outside of the barrel. There are various methods, such as machine grinding or sand cleaning, to make the barrel look clean and tidy.
12.裝桶篩用桶篩代替制桶篩，這個過程是用專門的機器操作。
12. Using a drum screen instead of a drum screen is a process that is operated by a specialized machine.
13.測試 是測試。用熱水測試桶是否滲漏，熱水有壓力，可以測試出桶是否滲漏。如果發現滲漏，可以修補或重換桶板。一些釀酒師愿意購買未用熱水測試的橡木桶，認為熱水會引發霉菌及其它問題。
13. Testing is testing. Use hot water to test the bucket for leaks. If the hot water is under pressure, the bucket can be tested for leaks. If leakage is found, the barrel board can be repaired or replaced. Some winemakers are willing to purchase oak barrels that have not been tested with hot water, believing that hot water can cause mold and other problems.
This article is organized and published by stainless steel inner solid wood wine barrels. Have you gained some understanding of these contents? For more information, please click on: http://www.lmkxbs.cn We will have more exciting content waiting for you to check out.
自動售酒機 2024-07-25 
