亚洲欧美日韩一区二区三区四区,日韩人妻精品一区二区在线推荐,黑丝翘臀后入在线观看,精品精品亚洲高清a毛片

When using the brewing equipment, you must not panic if the brewing equipment has shutdown failure. This is actually some common problems in the use of many equipment. Let me tell you this.

1.立即關閉釀酒設備的料斗門，盡可能擠出桶內多余的物料；切斷電源和水源，取下模具上的加熱元件，然后取下模具，然后用專用工具取下螺釘。如果要生產聚烯烴材料，不得拆卸螺釘。但是，如果出現嚴重的機械故障，一般很難在短時間內恢復生產，將螺釘取出進行清洗。

1. Immediately close the hopper door of the brewing equipment and squeeze out the excess materials in the barrel as much as possible; Cut off the power and water supply, first remove the heating element on the die, then remove the die, and then remove the screw with a special tool. If polyolefin material is to be produced, the screws must not be removed. However, in case of serious mechanical failure, it is generally difficult to resume production in a short time. Take out the screws for cleaning.

2.用銅或鋁工具清洗螺桿、機筒和模具，并仔細檢查零件表面是否有磨損和傷痕。如果有的話，用油石仔細打磨。釀酒設備安裝模具的壓蓋也應仔細打磨。

2. Clean the screw, barrel and die with copper or aluminum tools, and carefully check whether there are wear and scars on the surface of parts. If any, polish it carefully with an oilstone. The gland of the installation mould of brewing equipment shall also be carefully polished.

3.如果釀酒設備按上述方法清理后沒有啟動，檢查臨時停機的原因。如果不能立即恢復生產，應先用油脂垂直懸掛螺釘，然后再安排故障排除和維修。設備修補后，重新安裝螺桿，在用于安裝模具的螺栓上涂抹耐高溫油脂，然后安裝模具。螺栓應該對角擰緊。如果條件允許，使用扭矩扳手，以確保模具不會泄漏，并且再次拆卸非常方便。

3. If the brewing equipment is not started after cleaning according to the above methods, first check the causes of temporary shutdown. If production cannot be resumed immediately, hang the screws vertically with grease first, and then arrange troubleshooting and maintenance. After the equipment is repaired, reinstall the screw, apply high-temperature grease on the bolts used to install the mold, and then install the mold. Bolts should be tightened diagonally. If conditions permit, use a torque wrench to ensure that the die will not leak and it is very convenient to disassemble again.

4.由于釀酒過程沒有得到很好的控制，因此有必要找出釀酒設備操作過程失控的原因并加以。例如，是因?yàn)闇囟瓤刂苾x表出了故障還是熱電偶沒有正確插入。

4. Because the brewing process is not well controlled, it is necessary to find out the causes of out of control in the operation process of brewing equipment and solve them. For example, is it because the temperature control instrument fails or the thermocouple is not inserted correctly.

以上就是釀酒設備停機時我們應該做的。正確的預防和有用的維護是提高釀酒設備使用效率的基本保證。對于釀酒設備的突然關機，雖然出現不多，但也不能忽視。

The above is what we should do when the brewing equipment is shut down. Correct prevention and useful maintenance are the basic guarantee to improve the use efficiency of brewing equipment. The sudden shutdown of brewing equipment is rare, but it can not be ignored.