亚洲欧美日韩一区二区三区四区,日韩人妻精品一区二区在线推荐,黑丝翘臀后入在线观看,精品精品亚洲高清a毛片

Wine is playing an increasingly important role in people's life. People either use it to entertain guests and friends, or use it to comfort body and mind, or for other purposes. But since everyone likes wine so much, how much do you know about small brewing equipment? Now, let's meet the brewing equipment manufacturer.

在用釀酒設備進行釀酒時，大火燒開，為確保酒的口感不受沸點低的物質影響，應使原料的溫度達到80℃左右，這樣酒被釀造出來就不會有雜味，度數也不會太高。如果要想釀造出我們想要的酒，在出酒后火力就要減小，不要一直加火，不然出來的酒口感就會比較差。

When brewing with brewing equipment, the fire will boil. In order to ensure that the taste of the wine is not affected by substances with low boiling point, the temperature of raw materials should reach about 80 ℃, so that the wine will not have miscellaneous taste and the degree will not be too high. If we want to brew the wine we want, the fire power should be reduced after the wine is produced. Don't add fire all the time, otherwise the wine will taste worse.

酒被釀造出來之后，要將其進行冷卻。因此要格外注意火候?；鹆μ螅托⌒歪劸圃O(shè)備的冷卻速度不一致時，出來的酒就會發熱，口感復雜，不僅不好喝，產量也會下降。另外，火候也會影響到酒的質量。一般正常的小型釀酒設備在出酒時都是先出高度酒，后出低度酒，酒的度數慢慢下降。

After the wine is brewed, it should be cooled. Therefore, pay special attention to the fire. When the firepower is too large and the cooling rate is inconsistent with that of small brewing equipment, the wine will be hot and taste complex. It is not only bad to drink, but also the output will decrease. In addition, the heat will also affect the quality of the wine. Generally, the normal small-scale brewing equipment produces high alcohol wine first, and then low alcohol wine, and the alcohol level decreases slowly.

酒也成為生活中不可缺少的產品了，為了生產出來酒，釀酒設備關重要，為了提高生產效率，降低成本，經過不斷的研究，將傳統的釀造工藝設計到設備中進行釀酒。但是使用任何設備都會出現問題，使用釀酒設備過程中如果發生漏水情況，我們應該怎么？

Wine has also become an indispensable product in life. In order to produce wine, brewing equipment is very important. In order to improve production efficiency and reduce cost, through continuous research, the traditional brewing process is designed into the equipment for brewing. However, there will be problems when using any equipment. If water leakage occurs during the use of brewing equipment, how should we solve it?

一、釀酒設備位置受溫度影響，低于-13.2℃的情況不能用錫焊進行修復，在這種低溫下，錫會在金屬晶格中轉變成粉末狀的灰色錫，從而會造成焊點滲漏現場。當氣溫上升時就又出現漏水現場。

1、 The location of brewing equipment is affected by temperature. If it is lower than - 13.2 ℃, it cannot be repaired by tin welding. At this low temperature, tin will change into powdery gray tin in the metal lattice, resulting in solder joint leakage. When the temperature rises, water leakage occurs again.

二、較厚的釀酒設備出現問題，可以鉆孔用不銹鋼螺旋維修；對于很薄的釀酒設備只能用防水膠修補，才不會損壞設備。在清理裂紋處的油污時，用砂布打磨氧化膜，再用螺絲刀或斷鋸條刮除干凈，用噴燈將鋁件加熱，溫度不能太高控制在300℃-400℃，將焊條在裂紋處涂擦，當焊條熔化時，用螺絲刀將熔化的焊條合金在裂紋處摩擦，再逐步加厚焊層。

2、 If the thicker brewing equipment has problems, it can be drilled and repaired with stainless steel screw; For very thin brewing equipment, it can only be repaired with waterproof glue so as not to damage the equipment. When cleaning the oil stain at the crack, polish the oxide film with emery cloth, scrape it with a screwdriver or saw blade, heat the aluminum parts with a blowtorch, control the temperature at 300 ℃ - 400 ℃, and wipe the welding rod at the crack. When the welding rod melts, use a screwdriver to rub the molten welding rod alloy at the crack, and then gradually thicken the welding layer.

三、很多地方在修復時需要注意很多細節，我們必須了解設備的特點并掌握細節。釀酒設備如果出現問題我們可以會有一個又快又好的辦法。

3、 Many places need to pay attention to many details during repair. We must understand the characteristics of the equipment and master the details. If there is a problem with brewing equipment, we can have a fast and good solution.